index

<< Back
The DYS F4 V2 Pro is a flight controller with high performance, is designed for FPV hobbyists. Not only do they combine a PDB board together with flight control, but also an integrated OSD, current meter, voltmeter and built-in high power BEC etc functions.

DYS F4 PRO V2 flight control can meet all the functions you need include FPV racer, aerobatic flight and aerial photograph.

Specification:

Betaflight “DYS F4 PRO” firmware
STM32F405 master with higher refresh rate and more function ports
5V 3A BEC output
9V 1.2A BEC output
3.3V 0.3A BEC output
Compatible all split-type escs, connect with DYS 4-in-1 esc (F20A or F30A) with flexible flat cable
Support BF setting software to flash and debug OSD
Integrated current sensor to monitor the power consumption etc in real time
Use remote control to view flight control parameter through OSD
Support SAMRT AUDIO, adjust the VTX by OSD
Comes with heat resistance damping ball to upgrade the stability and operation
3-6s lipo input, integrated PDB, max withstand current 160A
Net weight 10.5g, exclude the cable
The refresh rate of PID and gyro up to 8K

Data

* Whole size: L 38mmX W 38mm, hole distance 30.5X30.5mm
* Six-layer PCB board and 3OZ copper to enhance the over-current and heat dissipation
* PDB board with reverse high voltage protection circuit
– MCU: STM32F405 GRT6
– IMU: MPU-6000
– OSD: AT7456E
– FLASH: 8M memory
– Current sensor: 0-200A
– Integrated reverse high voltage protection circuit
– Integrated circuit protection to USB port
– 3.3V LDO to power on internal circuit
– 9V BEC: 1.2A
– 5V BEC: 3A/ one-way output to avoid external interference
– When use with 4-in-1 esc, plug in the battery to supply the flight control instead of BEC.

Connection

DYS F4 PRO V2 flight control wiring diagram
V+ V- : For esc power cable
S1-S6：For GND of the corresponding esc signal cable
BOOT: BOOT button ( for firmware flash)
5V: 3A output, can connect with VTX, receiver, lens etc 5V power device at the same time
9V：1.5A output, can connect with wide voltage device, such as 7-24V power VTX etc.
3.3V：Power supply for DSMX etc 3.3V power device
GND: Negative
Vout: Video output for VTX image signal cable
Vin： Video input for camera signal cable
LED: Programmable LED signal cable output
RX1: For sbus etc receiver
PPM：For PPM receiver signal pad
USart6 tx：Smart Audio set the VTX function( The VTX should support to use Smart Audio function)
BAT+/BAT-: Battery voltage
Buzz-、Buzz+: Wiring for buzzer
Installation with DYS 4-in-1 esc (optional)
DYS F4 PRO V2 flight control plus f30a esc
Connect DYS F20A or F30A with flexible flat cable, no need to solder

Note

* Please mount the mini F4 with the 4-in-1 esc as pic shows. Be attention that do avoid damage the socket

While using with 4-in-1 esc

* Please solder the battery power cable with esc power cable, do not connect with battery

* The current meter will be no use when use with 4-in-1 esc

* With voltage detection for battery

Caution

* Please be attention to below attentions, otherwise your flight control will work improperly or damage.

* Please be always attention for the polarity. Double check before power on.

* Please keep the power off while plug or pull or any connection.

* Do not short the 5V or battery port, otherwise the flight control will be burnt

* After finished assemble, please check carefully and clean the residual solder splash to avoid short the components.

* Please mount the damping ball on the flight control (Equipped with accessory bag).

* If connect with 4-in-1 esc, please ensure the installation connect properly. Please do not force to plug or pull.

index

Helicopters • Airplanes • Drones • Builds • Repairs • Consulting • 3D Printing

Specification:

Data

Connection

Note